Ampli Lax R813

The constant-resistance amplifiers, R800, which features high performance and superior load capacity with compact light weight crust. They are capable of managing to drive high power full range speakers and subwoofers. R800?s bridge rectifier stack applies high current square stack that could make sure the current stability, without any block. It adopts a kind of independent shielding way for the high voltage helping to decrease the signal interference to the lowest point and also making sure the safety. And R800 applies on semi?s amplifier tube that was made in USA which brings R800 better dynamic range, higher safety standard and makes R800 bear bigger current impact, as the tubes are critically selected for keeping consistency of each amp and minimize the distortion. As for the signal process, the power is supplied directly from the main PCB, and then the power is much stable, clean and sufficient. This does great help on getting clearer and powerful sound. Moreover, due to the reasonable cable layout, the interference between channels is decreased effectively when the signal is input/output. R800 also features very low THD, SMPTE-IM and transient intermodulation interference.

Using High performance Onsemi amplifier tube made in USA.
Adapt to EIA standard (EIA RS-310-B),2U crust design.
Aluminum alloy front panel with brushed finish and detachable ventilated heat sink panel.
Each channel has a logic power supply which can control circuit to adjust power output stage dynamically in real time.
Providing versatile protection such as DC protection, internal fault protection, input overload protection, radio frequency interference filter, output short-circuit protection,mismatching the load and high frequency overload protection, radiator and transformer over-temperature protection, power input over-current protection.
High efficiency wind tunnel heat sink design.
Using differential input mode, faster reaction rate.
Class A sound quality, class H high power and low consumption.

The constant-resistance amplifiers, R800, which features high performance and superior load capacity with compact light weight crust. They are capable of managing to drive high power full range speakers and subwoofers. R800?s bridge rectifier stack applies high current square stack that could make sure the current stability, without any block. It adopts a kind of independent shielding way for the high voltage helping to decrease the signal interference to the lowest point and also making sure the safety. And R800 applies on semi?s amplifier tube that was made in USA which brings R800 better dynamic range, higher safety standard and makes R800 bear bigger current impact, as the tubes are critically selected for keeping consistency of each amp and minimize the distortion. As for the signal process, the power is supplied directly from the main PCB, and then the power is much stable, clean and sufficient. This does great help on getting clearer and powerful sound. Moreover, due to the reasonable cable layout, the interference between channels is decreased effectively when the signal is input/output. R800 also features very low THD, SMPTE-IM and transient intermodulation interference.

Using High performance Onsemi amplifier tube made in USA.

Adapt to EIA standard (EIA RS-310-B),2U crust design.

Aluminum alloy front panel with brushed finish and detachable ventilated heat sink panel.

Each channel has a logic power supply which can control circuit to adjust power output stage dynamically in real time.

Providing versatile protection such as DC protection, internal fault protection, input overload protection, radio frequency interference filter, output short-circuit protection,mismatching the load and high frequency overload protection, radiator and transformer over-temperature protection, power input over-current protection.

High efficiency wind tunnel heat sink design.

Using differential input mode, faster reaction rate.

Class A sound quality, class H high power and low consumption.

- See more at: http://www.envirel.de/Audio-engineering/Amplifiers/LAX-R813::13883.html?language=gb#sthash.IDYyTFyZ.dpuf

Ampli Lax R813

Using High performance Onsemi amplifier tube made in USA.
Adapt to EIA standard (EIA RS-310-B),2U crust design.
Aluminum alloy front panel with brushed finish and detachable ventilated heat sink panel.
Each channel has a logic power supply which can control circuit to adjust power output stage dynamically in real time.
Providing versatile protection such as DC protection, internal fault protection, input overload protection, radio frequency interference filter, output short-circuit protection,mismatching the load and high frequency overload protection, radiator and transformer over-temperature protection, power input over-current protection.
High efficiency wind tunnel heat sink design.
Using differential input mode, faster reaction rate.
Class A sound quality, class H high power and low consumption.

x

Đánh giá: